smart-home

提交图

作者	SHA1	备注	提交日期
Bernd Gottschlag	08546c2e36	Re-enable dynamic packet length The nrf24l01 used on the boards is probably a counterfeit chip. It cannot acknowledge received packets (probably a bit flip of the NO_ACK bit described here: https://ncrmnt.org/2015/03/13/how-do-i-cost-optimize-nrf24l01/) if the dynamic packet length is disabled.	5 年前
Bernd Gottschlag	fe5cd5fc86	Add delay after setting the pull ups for pin programming Without it the bits are sometimes read incorrectly.	5 年前
Bernd Gottschlag	9694fa3913	Fix the rx0 address The address was set for the wrong address and thus the module could not receive acks from the base station	5 年前
Bernd Gottschlag	f78e2f65c6	Disable the dynamic packet length The packet length is now fixed to 32 bytes.	5 年前
Bernd Gottschlag	608a6ee253	Fix generation of the salt	5 年前
Bernd Gottschlag	05696f7e74	Fix decryption bug	5 年前
Bernd Gottschlag	1381cb6634	Add encryption for the sent packet	5 年前
Bernd Gottschlag	3a21aef881	Rework the makefile and optimize the code for flash space	5 年前
Bernd Gottschlag	8a49c011c9	Update packet protocoll	5 年前
Bernd Gottschlag	58a48e5230	Fix order of the element count and packet type bit field	5 年前
Bernd Gottschlag	e435620c91	Add a new packet format with the calculation of the CRC	5 年前
Bernd Gottschlag	c86399b66e	Add the calculation of a crc The algorith used is for the CRC-16-CCITT, also known as CRC-KERMIT.	5 年前
Bernd Gottschlag	30fe01bb9e	Generate an ID according to the dip switches The ID is used as the last byte of the RX address. It is also sent as a part of the data packet to allow assigning the sending station to a packet.	5 年前
Bernd Gottschlag	3dcfae6196	Change the way the TX and RX addresses are written to the nrf24l01	5 年前
Bernd Gottschlag	e7bfca4363	Use the IRQ signal from the nrf24l01 instead of polling the status This is done to avoid transmission erros as described in https://forum.mysensors.org/topic/10452/nrf24l01-communication-failure-root-cause-and-solution	5 年前
Bernd Gottschlag	f7bfdf101c	Add definitions of the IRQ pin to the nrf24l01	5 年前
Bernd Gottschlag	1dd0f89149	Fix pin definitions of the interface to the nrf24l01	5 年前
Bernd Gottschlag	011303042b	Remove a variable that caused a compiler warning	5 年前
Bernd Gottschlag	f1b0ebf618	Move SPI initialization and pin definitions to spi.c	5 年前
Bernd Gottschlag	204ff8d220	Add power save mode and send messages every 7.5s	5 年前
Bernd Gottschlag	0c03c24fcd	Change the MCU to the Atmega88 The pin definitions are updated and the uart debug interface is removed as it is not present on the actual board.	5 年前
Bernd Gottschlag	ddb5b0426e	Send the data from the BME280 with the NRF24L01	5 年前
Bernd Gottschlag	01dff7cfd3	Use spi functions	5 年前
Bernd Gottschlag	93fd7841a9	Use spi functions	5 年前
Bernd Gottschlag	9d1b611356	Use dedicated function to read the status register when transmitting	5 年前
Bernd Gottschlag	fc26a37348	Set the transmission retries and time-out duration to each maximum	5 年前
Bernd Gottschlag	b9cfc34e94	Flush TX FIFO after an unsuccessful transmission	5 年前
Bernd Gottschlag	45f19e8c43	Fix register struct definitions	5 年前
Bernd Gottschlag	5ee6bbbf1a	Add SPI interface functions	5 年前
Bernd Gottschlag	7f1da0221c	Update .gitignore	5 年前
Bernd Gottschlag	e5ad15dbfa	Add reading from the BME280 using the official API Currently the data values are written to the debug output.	5 年前
Bernd Gottschlag	780cedcbc4	Fix order of the bit fields of the register definitions	5 年前
Bernd Gottschlag	278f7f23fe	WIP: use register definitions to access them	5 年前
Bernd Gottschlag	b487ab67f6	Add nRF24L01 register definitions	5 年前
Bernd Gottschlag	33e1d5e700	WIP tidy up the NRF24L01 code	5 年前
Bernd Gottschlag	347211065c	Add prototyping code for sending a dummy message with the nrf24l01 The firmware is developed using an aduino micro pro with an atmega32u4 as the hardware for the weather station is not ready yet.	5 年前
Bernd Gottschlag	daf929f3d2	Add digikey link for a part	5 年前

37 次代码提交 (08546c2e368cce66e68ae6e442802172f64e43d5)