smart-home

Commit-Graf

Upphovsman	SHA1	Meddelande	Datum
Bernd Gottschlag	1a527b5929	Re-enable dynamic packet length The nrf24l01 used on the boards is probably a counterfeit chip. It cannot acknowledge received packets (probably a bit flip of the NO_ACK bit described here: https://ncrmnt.org/2015/03/13/how-do-i-cost-optimize-nrf24l01/) if the dynamic packet length is disabled.	5 år sedan
Bernd Gottschlag	f30f7c71a9	Add delay after setting the pull ups for pin programming Without it the bits are sometimes read incorrectly.	5 år sedan
Bernd Gottschlag	0d7211d770	Fix the rx0 address The address was set for the wrong address and thus the module could not receive acks from the base station	5 år sedan
Bernd Gottschlag	e6669484e6	Disable the dynamic packet length The packet length is now fixed to 32 bytes.	5 år sedan
Bernd Gottschlag	b10df03e01	Fix generation of the salt	5 år sedan
Bernd Gottschlag	05696f7e74	Fix decryption bug	5 år sedan
Bernd Gottschlag	1381cb6634	Add encryption for the sent packet	5 år sedan
Bernd Gottschlag	3a21aef881	Rework the makefile and optimize the code for flash space	5 år sedan
Bernd Gottschlag	8a49c011c9	Update packet protocoll	5 år sedan
Bernd Gottschlag	58a48e5230	Fix order of the element count and packet type bit field	5 år sedan
Bernd Gottschlag	e435620c91	Add a new packet format with the calculation of the CRC	5 år sedan
Bernd Gottschlag	c86399b66e	Add the calculation of a crc The algorith used is for the CRC-16-CCITT, also known as CRC-KERMIT.	5 år sedan
Bernd Gottschlag	30fe01bb9e	Generate an ID according to the dip switches The ID is used as the last byte of the RX address. It is also sent as a part of the data packet to allow assigning the sending station to a packet.	5 år sedan
Bernd Gottschlag	3dcfae6196	Change the way the TX and RX addresses are written to the nrf24l01	5 år sedan
Bernd Gottschlag	e7bfca4363	Use the IRQ signal from the nrf24l01 instead of polling the status This is done to avoid transmission erros as described in https://forum.mysensors.org/topic/10452/nrf24l01-communication-failure-root-cause-and-solution	5 år sedan
Bernd Gottschlag	f7bfdf101c	Add definitions of the IRQ pin to the nrf24l01	5 år sedan
Bernd Gottschlag	1dd0f89149	Fix pin definitions of the interface to the nrf24l01	5 år sedan
Bernd Gottschlag	011303042b	Remove a variable that caused a compiler warning	5 år sedan
Bernd Gottschlag	f1b0ebf618	Move SPI initialization and pin definitions to spi.c	5 år sedan
Bernd Gottschlag	204ff8d220	Add power save mode and send messages every 7.5s	5 år sedan
Bernd Gottschlag	0c03c24fcd	Change the MCU to the Atmega88 The pin definitions are updated and the uart debug interface is removed as it is not present on the actual board.	5 år sedan
Bernd Gottschlag	ddb5b0426e	Send the data from the BME280 with the NRF24L01	5 år sedan
Bernd Gottschlag	01dff7cfd3	Use spi functions	5 år sedan
Bernd Gottschlag	93fd7841a9	Use spi functions	5 år sedan
Bernd Gottschlag	9d1b611356	Use dedicated function to read the status register when transmitting	5 år sedan
Bernd Gottschlag	fc26a37348	Set the transmission retries and time-out duration to each maximum	5 år sedan
Bernd Gottschlag	b9cfc34e94	Flush TX FIFO after an unsuccessful transmission	5 år sedan
Bernd Gottschlag	45f19e8c43	Fix register struct definitions	5 år sedan
Bernd Gottschlag	5ee6bbbf1a	Add SPI interface functions	5 år sedan
Bernd Gottschlag	7f1da0221c	Update .gitignore	5 år sedan
Bernd Gottschlag	e5ad15dbfa	Add reading from the BME280 using the official API Currently the data values are written to the debug output.	5 år sedan
Bernd Gottschlag	780cedcbc4	Fix order of the bit fields of the register definitions	5 år sedan
Bernd Gottschlag	278f7f23fe	WIP: use register definitions to access them	5 år sedan
Bernd Gottschlag	b487ab67f6	Add nRF24L01 register definitions	5 år sedan
Bernd Gottschlag	33e1d5e700	WIP tidy up the NRF24L01 code	5 år sedan
Bernd Gottschlag	347211065c	Add prototyping code for sending a dummy message with the nrf24l01 The firmware is developed using an aduino micro pro with an atmega32u4 as the hardware for the weather station is not ready yet.	5 år sedan
Bernd Gottschlag	daf929f3d2	Add digikey link for a part	5 år sedan

37 Incheckningar (atmega_88)